main logo

Strike Pack Ps4

I 10 migliori prodotti di settembre 2024
Ultimo aggiornamento: 25 settembre 2024
Semaiki
Semaiki
Paddles Strike per controller PS4, attacco per il pulsante posteriore Controller PS4, attacco per il pulsante posteriore F.P.S. Dominator Mod Kit per controller PS-4
Spedizione gratuita
star

98

QUALITÀ MASSIMA

VEDI SU AMAZON
Amazon.it
#2

  • Impostazione della funzione di programmazione - Premere a lungo il pulsante SET per 2 secondi, il LED corrispondente a × lampeggia rapidamente (4HZ), quindi premere brevemente il pulsante M1 o M2, il LED lampeggia lentamente sul display della funzione corrispondente (la sequenza di lampeggiamento è X, ○, △, □, R3, L3, R2, L2, R1, L1).
  • Impostazione della funzione di programmazione - Quindi premere il pulsante SET, la funzione corrispondente sarà mappata su M1 / 2; ad esempio: quando si entra in modalità di programmazione, premere il pulsante M1 per visualizzare il LED su R1, quindi premere nuovamente il pulsante SET, il LED su R1 diventa a luce lunga, la funzione M1 è R1; quando si programma M2, è simile a quanto sopra.
  • Annullamento della funzione - Premendo a lungo il tasto SET per 5 secondi, il LED di programmazione passa da lampeggiante veloce a spento e la funzione M1 / 2 viene annullata.
  • Funzione di memoria del pulsante di programmazione - Inserire il pulsante di estensione posteriore nell'impugnatura, se M1 / 2 non ha alcuna funzione, il LED1 lampeggerà lentamente (2HZ) per 3 secondi e poi si spegnerà, premere a lungo il pulsante SET per entrare nella modalità di programmazione e quindi il LED1 lampeggerà rapidamente. Se M1 / 2 ha memorizzato l'ultima funzione di programmazione, il LED corrispondente si accende a lungo.
  • Impostazione della funzione TURBO - Tenendo premuto contemporaneamente il pulsante di funzione e il pulsante Turbo, il pulsante di funzione attiva la funzione Turbo burst; premere di nuovo il suddetto pulsante combinato per annullare la funzione Turbo. Se la funzione Turbo è attiva, dopo aver premuto il pulsante, il LED corrispondente alla funzione lampeggia rapidamente (4HZ).
  • 16,99 € SU AMAZON
AUELEK
AUELEK
Strike Pack for Playstation 4,Back Button Attachment,Back Control Fastening for Playstation 4 Wireless Controller,FPS Strike Pack Rear Button for Game Controller Accessory with Joystick Cap
Spedizione gratuita
star

79

QUALITÀ BUONA

VEDI SU AMAZON
Amazon.it
#7

  • ➤【Setting the Programming Function】Press and hold the set button for 2 seconds, the corresponding LED light from × flashes quickly (4 Hz), and briefly press the M1 or M2 button. The LED light flashes slowly on the screen of the corresponding function (the flashing) sequence is ×, O, O, R3, L3, R2, L2, R1, L1)
  • ➤【M1, M2 Mapping Setting Key】Then press the SET button. The corresponding function is assigned to M1/2. For example: when you switch to programming mode, press the M1 button to display the LED on R1, then press the SET button again. The LED on R1 lights up for a long time. The M1 function is R1. When programming M2, this is similar to the above.
  • ➤【Programmed Button Memory Function】Insert the rear extension button into the handle. If M1/2 does not work, LED1 flashes slowly (2Hz) for 3 seconds and then goes out. Long press the SET button to enter programming mode, and LED1 flashes quickly. If M1/2 has saved the last programming function, the corresponding LED will light up for a long time.
  • ➤【Cancel Function】Press the set button for 5 seconds, the programming display LED changes from fast flashing to the M1/2 function is deleted.
  • ➤【Turbo-Burst Function Setting】 Hold down the function key and turbo button at the same time, which have Turbo Burst function. Press the top combination button again to cancel the turbo function of the button. When the turbo function is set, press after pressing the button, the LED corresponding to the function flashes quickly (4Hz).
  • 18,18 € SU AMAZON