Elrs
I 10 migliori prodotti di settembre 2024
Ultimo aggiornamento:
29 settembre 2024
BETAFPV
BETAFPV ExpressLRS 2.4G Lite Receiver with Flat SMD Ceramic Antenna High Refresh Rate Long Range Performance Compatible for 65/75/85mm FPV Racing Whoop Drone
Spedizione gratuita
98
QUALITÀ MASSIMA
VEDI SU AMAZON
Amazon.it
#1 VINCITORE
▼ Mostra di più
▲ Mostra di meno
【Performance】Ultralight ELRS Lite receiver has a 2.4GHz Flat SMD ceramic antenna. A solid flat antenna without irregular parts can withstand crashes, making the receiver not so fragile. Perform well in control, range and stability, bringing a good flight experience to pilots
【Weight&Size】New lite receiver with a flat antenna features a 3mm extra-thin board and 0.53g lightweight, which requires less assembly space on drones with limited space
【ExpressLRS】 ExpressLRS is an open-source RC link for RC applications, based on Semtech Lora SX127x or SX1280 hardware for RX and TX respectively. This makes ExpressLRS one of the fastest RC links available while still offering long-range performance
【ExpressLRS Lite Receiver】BETAFPV ELRS Lite receiver is based on the ExpressLRS project, an open-source RC link for RC applications that aims to achieve the best possible link performance in both speeds, latency, and range suit for ELRS TX module, etc
【Configuration & Bind】The Lite receiver comes with officially major release V1.1.0 protocol and no Binding Phrase included. Lite receiver could enter binding status by power on/off three times
16,99 € SU AMAZON
BETAFPV
BETAFPV ELRS 2.4GHz Micro Receiver Support 5 CH PWM Outputs Failsafe Function with IPEX MHF T Antenna Compatible for Multirotors Fixed-Wing Helicopters RC Cars Boats Easy to Install Plug and Play
Spedizione gratuita
96
QUALITÀ SUPERIORE
VEDI SU AMAZON
Amazon.it
#2
▼ Mostra di più
▲ Mostra di meno
【PWM Output】BETAFPV ELRS Micro receiver is the first ELRS receiver with PWM output on BETAFPV. Supports 5 channels PWM outputs. It also supports flash CRSF output firmware, in this case CH2 corresponds to TX and CH3 corresponds to RX
【Application】ELRS micro receiver adapts for multiple types of models like fixed-wing, helicopters, RC cars, boats and etc.
【Failsafe Function】When the connection or signal is lost between the radio transmitter and receiver, the failsafe function will adjust all the channels to the failsafe values set by the users, maximum keep safety and prevent from flying away. It's necessary to set up failsafe values properly if you are not using a flight controller, such as RC fixed-wing
【Weight&Size】Weighing about 4.5g with an antenna and with the sizes of 19mm*32mm*9mm (without antenna). It means that an FPV drone can not afford to carry.
【Plug &Play】With the plug-and-play connect ports, micro receiver is very easy to use and does not need to solder
16,99 € SU AMAZON
BETAFPV
BETAFPV ELRS 868 MHz Nano Ricevitore Ottenere Prestazioni a Lungo Raggio in entrambe Le velocità, latenza e Gamma
Spedizione gratuita
95
QUALITÀ OTTIMA
VEDI SU AMAZON
Amazon.it
#3
▼ Mostra di più
▲ Mostra di meno
【ExpressLRS】 ExpressLRS is an open-source RC link for RC applications, based on Semtech Lora SX127x or SX1280 hardware for RX and TX respectively. This makes ExpressLRS one of the fastest RC links available while still offering long-range performance.
【ExpressLRS Receiver】 BETAFPV Nano receiver is based on the ExpressLRS project, an open-source RC link for RC applications which aims to achieve the best possible link performance in both speeds, latency, and range suit for ELRS TX module or Nano bay, etc.
【Crossfire Serial Protocol 】 ExpressLRS uses the Crossfire serial protocol (AKA CRSF protocol) to communicate between the receiver and the flight controller board. So make sure your flight controller board supports the CRSF serial protocol. How to set up the CRSF protocol can be viewed on the fourth page of the manual.
【Nano Size】 This receiver only has 0.7 grams and the volume is 12mm*19mm which is very suitable for Tiny whoop because of the ultra light and Nano size.
【Configuration & Bind】Nano receiver could enter binding status by power on/off three times. Step: Plugin and unplug nano receiver three times; Make sure the LED is doing a quick double blink, which indicates the receiver is in bind mode; Make sure the RF TX module or radio transmitter enter binding status, which sends out a binding pulse; If the receiver has a solid light, it's bound.
22,99 € SU AMAZON
BETAFPV
BETAFPV SuperD ELRS Diversity Receiver with Dual Receiver Chains 2 Antennas TXCO Tech Support CRSF Protocol for FPV Drone Fixed-Wing Aircraft Long Range Flying Aerial Photography FPV Freestyle Tricks
Spedizione gratuita
88
QUALITÀ DISTINTA
VEDI SU AMAZON
Amazon.it
#4
▼ Mostra di più
▲ Mostra di meno
【TXCO Tech】SuperD ELRS 2.4G Diversity Receiver is built-in a TCXO (temperature compensated crystal oscillator), which is shared by two RF chips for a super accurate clock source. The true diversity receiver including two RF chips and PA+LNA will generate a large amount of heat when working. With the high-quality TCXO, it can withstand extreme temperatures with no fear of heat and cold, continuously outputting accurate frequency for long range flight.
【Dual RF Receiver Chains】SuperD ELRS 2.4G Diversity Receiver with two complete RF receiver chains (referring to PA+LNA+SX1280), ensuring longer and more stable flying for FPV drones and RC airplanes. Based on the latest official ExprssLRS. It comes with ExpressLRS V3.0.0 firmware.
【Two Dipole T Antennas】SuperD ELRS 2.4G Diversity Receiver comes with Two Dipole T antennas, it will create an omnidirectional signal for good signal transmission. Placing the antenna separately and vertically as far part as possible to get a better signal is recommended.
【Compatible Products】Not only it is used for FPV drones but also for FPV fixed-wing, or other FPV aircraft. It has superb performance in long range flying. It greatly fulfills the requirements of reliability for long range flying, aerial photography, or FPV freestyle tricks
【Ultralight Weight】 Ultralight weight only 1.1g without the antenna. The receiver board features a reasonable layout and is impeccably clean. Very easy to solder.
28,99 € SU AMAZON
BETAFPV
BETAFPV ELRS LiteRadio 3 Radio Transmitter RC Controller, Support FPV Simulator, Joystick Calibration, USB Charging, Compatible for RC Models Like Multirotor Airplane FPV Drone Quadcopter - Mode 2
Spedizione gratuita
84
QUALITÀ AFFIDABILE
VEDI SU AMAZON
Amazon.it
#5
▼ Mostra di più
▲ Mostra di meno
【Nano Joystick Gimbal】 LiteRadio 3 ha un Joystick Gimbal di nuova concezione. Con le estremità ergonomiche dello stick, lo stick è staccabile, antiscivolo e regolabile in altezza, ha una lunga longevità fino a 120.000 rotazioni. Il potenziometro offre precisione di posizionamento e sensibilità di risposta rapida, offrendo una buona esperienza al tuo volo
【Tempo di utilizzo prolungato】 Dotato di una batteria integrata da 2000 mAh 1S e di un modulo di ricarica, puoi caricare tramite USB e può funzionare fino a 15 ore senza un modulo esterno. Nel frattempo, ha progettato un avviso di basso consumo per indicare una batteria scarica. Indica una batteria scarica e deve essere ricaricata se la luce blu lampeggia lentamente e il cicalino emette un segnale acustico continuo
【Configuratore BETAFPV supportato】 Aggiornamenti LiteRadio 3 con il sistema LiteRadio personalizzato autosviluppato BETAFPV. I piloti possono utilizzare direttamente la calibrazione del joystick e l'aggiornamento del firmware sul trasmettitore radio o sul configuratore BETAFPV. BETAFPV Configurator è un'utilità progettata per semplificare l'aggiornamento, la configurazione e la sintonizzazione del trasmettitore radio. Facile e conveniente, soddisfa ulteriormente le tue diverse esigenze di volo
【Simulatore FPV supportato】LiteRadio 3 è ergonomico e ha la forma di un controller di gioco. Il rivestimento in gomma è comodo da tenere in mano e la texture antiscivolo sui manici consente una presa solida. Ha la funzione di un simulatore FPV che può fungere da joystick USB quando collegato a un PC e supporta la maggior parte dei simulatori sul mercato con una configurazione completa
【Nota】il firmware predefinito del trasmettitore radio LIteRadio 3 (ELRS 2.4G) è ELRS V3 da novembre 2023 invece della versione precedente ELRS V2.0. Il trasmettitore radio LiteRadio 3 ELRS V3 non supporta più un modulo TX esterno! ! !
76,99 € SU AMAZON
BETAFPV
BETAFPV ExpressLRS LiteRadio 2 SE Radio Transmitter Remote Controller with Built-in 1000mAh 1S Battery for FPV RC Racing Drones Multirotor Simulator Joystick Calibration - Mode 2 Left Throttle
30% Sconto
Spedizione gratuita
82
QUALITÀ AFFIDABILE
VEDI SU AMAZON
Amazon.it
#6
▼ Mostra di più
▲ Mostra di meno
【ExpressLRS 2.4G Protocol】BETAFPV ExpressLRS 2.4G LiteRadio 2 SE radio transmitter is the World's First ELRS radio controller. It comes with build-in ELRS 2.4G TX, which can achieve long-range flying with your drones
【BETAFPV Configurator】This transmitter supported BETAFPV Configuration with the function of radio controller setup, Full function of the ExpressLRS configuration, Channel mixer for fix wing drones, and firmware update. Easy and convenient, further to fulfilled your different fly requirement
【Performance】This ELRS 2.4G protocol radio transmitter built-in 1000mAh 1S battery, you can charge it by type-c cable instead of replacing battery. It has a total of 8 channels. Supports 3 RF powers of 25mW, 50mW and 100mW, and packet rates of 50Hz, 150Hz, 250Hz and 500Hz
【FPV Simulator】This transmitter has the function of FPV simulator like other versions of LiteRadio 2, which can act as a USB Joystick when connected to a personal computer, suitable for FPV novices to play FPV simulators like EREADRONE
【Technical Support & Warranty】We have a professional team and considerate after-sales service. If you have any questions, you can contact us by email, and we will definitely reply you within 24 hours. We offer a warranty for all goods within 3months!
41,99 € SU AMAZON
BETAFPV
BETAFPV SuperD ELRS Diversity Receiver with Dual RX Chains 2 Antennas TXCO Tech Support CRSF Protocol for FPV Drone Fixed-Wing Aircraft Long Range Flying Aerial Photography FPV Freestyle Tricks-868M
Spedizione gratuita
80
QUALITÀ BUONA
VEDI SU AMAZON
Amazon.it
#7
▼ Mostra di più
▲ Mostra di meno
【TXCO Oscillator】SuperD ELRS 868MHz Diversity Receiver is built-in a TCXO (temperature compensated crystal oscillator), which is shared by two RF chips for a super accurate clock source. With the high-quality TCXO, it can withstand extreme temperatures with no fear of heat and cold, continuously outputting accurate frequency for long-range flight.
【ELRS 868M】The first true diversity receiver for the 868MHz frequency bands, with two separate receiving modules working together to improve signal reception quality and overall reliability. The 868MHz radio system exhibits greater diffraction ability due to its lower frequency.
【Receivers&Antennas】BETAFPV SuperD 868MHz diversity receiver has two dual RF receiver chains with two Dipole T antennas, which will create an omnidirectional signal for good transmission, ensuring longer and more stable flying for FPV drones and RC airplanes.
【Compatible Items】Not only it is used for FPV drones but also for FPV fixed-wing, or other FPV aircraft. It has superb performance in long-range flying. It greatly fulfills the requirements of reliability for long-range flying, aerial photography, or FPV freestyle tricks.
【Notice】The SuperD ELRS 868MHz Diversity Receiver's default firmware is ELRS V3.3.0. The official version has not yet been released. It will be updated synchronously with the ELRS V3.3 version. Then you can check the latest ELRS Configurator Nightly to operate. Select the target device ''BETAFPV SuperD 900MHz RX''. Firmware for 868MHz is currently self-compiled firmware.
28,99 € SU AMAZON
Veenewy
Veenewy Ricevitore SX1280 ELRS 2.4GHz RX ExpressLRS Long Range alto tasso di aggiornamento per Drone FPV e Aereo RC EP1 RX. Facile da usare, durevole e finemente lavorato.
77
QUALITÀ BUONA
VEDI SU AMAZON
Amazon.it
#8
▼ Mostra di più
▲ Mostra di meno
Caratteristiche: I ricevitori si basano su architettura e programmi open source ExpressLRS. Offriamo 3 tipi di moduli ricevitori RX. Entrambi usano ESP8285 MCU. Il tuo firmware può essere aggiornato tramite WIFI, che è molto user-friendly.
Di solito devi solo al ricevitore. Una volta spento l'alimentazione elettrica e il , ExpressLRS può essere trovato caldo dopo 60 ore per impostazione predefinita. , accedi al punto di accesso tramite un computer o un telefono cellulare, la password è espressori, quindi puoi visitare 10.0.0.1 per scaricare il firmware del ricevitore.
L'aspetto, il colore e la stampa del prodotto possono variare da a ma ciò non influisce sull'utilizzo.
15,97 € SU AMAZON
HAPPYMODEL
HAPPYMODEL ELRS RX SX1280 EXPRESSLRS Ricevitore Nano a Lungo Raggio per Drone da Corsa Fai da Te (EP1 RX)
74
QUALITÀ BUONA
VEDI SU AMAZON
Amazon.it
#9
▼ Mostra di più
▲ Mostra di meno
Il ricevitore Happymodel ELRS Nano Series è un programma open source basato su ExpressLRS, i firmware precaricati sono tutte versioni beta.
Differenza MCU: PP RX con MCU STM32L432KBU6, mentre EP1 / EP2 RX con ESP8285 MCU.
Dettaglio antenna incorporata: PP/EP2 RX con antenna in ceramica SMD, mentre EP1 RX con antenna omnidirezionale. Differenza picco-guadagno: PP / EP2 _RX è 3,7 dB, mentre EP1_RX è 2,23 dB.
Caratteristica comune del ricevitore: aggiornamento tramite Wi-Fi; Tensione di lavoro 5V, modulo RF SX1280IMLTRT, frequenza di aggiornamento di ricezione: 25Hz - 500Hz.
Ricevitore LRS Comodo per Racing, Long Range e Tinywhoop, poiché sono leggeri, di dimensioni Nano e con modulo RF a bassa latenza e alta frequenza di aggiornamento.
24,98 € SU AMAZON
BETAFPV
BETAFPV Meteor75 Pro 1S Brushless Whoop Drone Quadcopter with 45mm 3-Blade Propellers for FPV Freestyle Racing Indoor Outdoor, Fly Time Up to 6min with BT2.0 550mAh 1S Lipo Battery-ELRS
Spedizione gratuita
66
QUALITÀ BUONA
VEDI SU AMAZON
Amazon.it
#10
▼ Mostra di più
▲ Mostra di meno
【Ultra-Powerful】Meteor75 Pro 1S brushless whoop quadcopter is the largest available 1S whoop on the current market. It can offer pilots a faster, more responsive flight experience, and longer flight time, which would be ideal for FPV racing or acrobatic flying indoors or outdoors.
【Frame&Propellers】Meteor75 Pro brushless whoop frame is built for the largest 1S brushless drone quadcopter. Featuring motor holders for convenient installation, and it is perfect for 45mm propellers. This combo performs very precisely, agile, and fantastic flying. It greatly enhances the thrust for 1S whoop
【Motors&Battery】Meteor75 Pro features updated powerful 22000KV 1102 motors and BT2.0 550mAh 1S battery, which provides a larger capacity and higher discharge rate, bringing more flight time and robust flight performance to the quadcopter.
【FC&ESC】Equipped with F4 1S 5A flight controller(Serial ELRS). The ELRS RX version comes with the default ELRS V2.0 firmware and supports being upgraded to ELRS V3.0 separately without flashing Betaflight FC firmware. The ESC on the board is powered by BB51 hardware in place of BB21, and the gyro to BOSH BMI270 for better performance and stability.
【Camera&Canopy】Built-in 1.45g ultralight and upgraded C03 FPV camera. This new camera has optimal performance for indoor whoop drones. Adopted with an injection molding technique, this canopy is 1.60g ultralight weight and is more durable, anti-ruin, and heat-resistant, providing good protection for the whoop drone.
142,99 € SU AMAZON
elrs modulo
modulo elrs
ricevente elrs
elrs pwm
fpv elrs
happymodel elrs
meteor85 elrs
radiomaster elrs
elrs tx
radiocomando elrs
#1 VINCITORE
